Treatment Technologies
UV Disinfection System Companies
UV disinfection suppliers for drinking water, wastewater, reuse, and industrial process disinfection with dose-validated reactors.
This page is a good fit if you need:
- Flat Sheet UF Membranes or Hollow Fiber RO capabilities
- Suppliers with food-beverage sector experience
- Providers operating in China or Indonesia
- Providers
- 10
- Verified
- 4
- Countries
- 8
Can't find the right fit? Post a brief and let qualified suppliers come to you.
Post a projectHow to choose a uv disinfection system provider
Start with providers that clearly operate in your target geography and project footprint.
Look for industry exposure that matches your water challenge, compliance constraints, and deployment context.
Use technologies, service scope, and proof signals to narrow the list before reaching out to suppliers.
Not sure where to start? Our experts can help.
Filter results
Verified providers
4 claimed companies in this category
Country
Industry
Technology
Find a UV Disinfection System Provider
Showing 1-10 of 10
10 results from 10 matched providers
UV Disinfection Systems: Dose Validation, Lamp Technology, and Regulatory Compliance
Ultraviolet (UV) disinfection inactivates pathogens by damaging DNA and RNA, preventing cellular replication. UV-C radiation (200 to 280 nm, peak germicidal effectiveness at 254 nm for low-pressure lamps; 200 to 300 nm broad spectrum for medium-pressure) is absorbed by nucleic acids, forming pyrimidine dimers (thymine-thymine, thymine-cytosine) that block DNA replication. Key regulatory doses: US EPA UV Guidance Manual (2006): Cryptosporidium 2 log inactivation requires 2.5 mJ/cm2 (less than 5 NTU, UVT greater than 95 percent); 4 log requires 22 mJ/cm2; Giardia 2 log requires 5.8 mJ/cm2; 3 log requires 12 mJ/cm2; adenovirus 4 log requires greater than 180 mJ/cm2 (UV resistant, requires higher dose). UK DWI UV Guidance: minimum dose 40 mJ/cm2 for potable water; additional dose reduction credit for Cryptosporidium per WRc/UKWIR risk assessment methodology. WHO UV Guidelines (2019): validate 40 mJ/cm2 delivered dose for drinking water. UV dose delivery (fluence rate): measured in mW/cm2 (mJ/cm2 equals mW/cm2 times seconds); actual delivered dose lower than theoretical due to UV transmittance (UVT) of water and hydraulic effects (flow non-uniformity).
UV lamp technologies: low-pressure (LP) lamps emit monochromatic UV at 253.7 nm; electrical efficiency 25 to 35 percent (UV output/electrical input); lamp power 30 to 300 W; lifetime 8,000 to 16,000 hours (annual replacement typically); optimal water temperature 20 to 40 degrees C (performance drops above 40 degrees C and below 15 degrees C). Low-pressure high-output (LPHO) lamps: higher power (100 to 500 W) at same germicidal efficiency as LP; fewer lamps per system. Medium-pressure (MP) lamps: polychromatic output 200 to 400 nm; higher power per lamp (1 to 40 kW); fewer lamps for equivalent dose; effective against UV-resistant viruses (adenovirus) and photoreactivation (UV-A also inactivates photolyase enzymes that repair UV damage in some pathogens). UV LEDs (light emitting diodes): solid-state UV-C at 260 to 280 nm; no mercury (environmental benefit); on/off switching; wall-plug efficiency 3 to 10 percent (improving rapidly, 2020 to 2025 period); current cost higher than lamp systems but rapidly decreasing; commercial point-of-entry LED UV systems available; large-scale mains UV LED systems emerging. Amalgam lamps: LP amalgam (mercury-amalgam alloy) maintain output across wider temperature range (5 to 40 degrees C); preferred for cold groundwater applications.
UV system validation and compliance: DVGW W 294 (German, widely referenced internationally) and USEPA Ultraviolet Disinfection Guidance Manual (UVDGM, 2006) specify bioassay-based dose-response validation using specific test organisms (MS2 coliphage for 40 mJ/cm2 validation, Bacillus subtilis spores for higher doses). NWRI/AWWARF (now Water Research Foundation) UV validation protocol: collimated beam test to determine log inactivation vs UV dose for surrogate organism; reactor validation test in biodosimetry reactor measuring RED (Reduction Equivalent Dose) as function of UVT and flow. UK UKWIR report 14/WW/07/27: UV validation for drinking water; DWI requires validation to DVGW W 294 or USEPA UVDGM for mains water disinfection. Operational monitoring: UV intensity sensors (calibrated to NIST standards); UVT monitoring (online spectrophotometer at 254 nm); flow measurement for dose calculation; alarm at 90 percent of validated minimum dose. USEPA Long-Term 2 Enhanced Surface Water Treatment Rule (LT2ESWTR): UV dose credits assigned based on validated reactor performance at validated UVT and flow combination (minimum point of compliance validation). CEFAS and UK monitoring: bacteriological water quality standards monitored by DWI, with UV failure triggering Drinking Water Safety Plan (DWSP) incident protocols.
Frequently Asked Questions
What UV dose is needed to inactivate Cryptosporidium?
UV dose requirements for Cryptosporidium inactivation (US EPA UV Guidance Manual 2006, validated by bioassay): 1 log (90 percent) inactivation: 1.6 mJ/cm2; 2 log (99 percent): 2.5 mJ/cm2; 3 log (99.9 percent): 12 mJ/cm2; 4 log (99.99 percent): 22 mJ/cm2. These are remarkably low doses compared to Giardia (5.8 mJ/cm2 for 2 log) and bacteria, because Cryptosporidium oocysts are highly resistant to chlorine but highly sensitive to UV. UK DWI standard minimum dose 40 mJ/cm2 provides greater than 4 log Cryptosporidium inactivation with substantial safety margin. For LT2ESWTR (US EPA): utilities with bin 2 to 4 Cryptosporidium occurrence must provide 2 to 5.5 log additional treatment; UV is typically the most cost-effective 2 to 3 log Cryptosporidium treatment credit. Important: UV dose must be the DELIVERED (validated) dose, not the theoretical lamp output dose; actual delivered dose is lower due to UVT losses and hydraulic non-uniformity. Photoreactivation risk: Cryptosporidium oocysts do not photoreactivate (no DNA photolyase enzyme), unlike some bacteria - UV inactivation of Cryptosporidium is permanent.
How is UV dose measured and validated?
UV dose (fluence, mJ/cm2) cannot be measured directly in an operating reactor; it is inferred from sensor readings and validated by bioassay. Validation process: (1) Collimated beam test (lab bench): determines log inactivation vs UV dose for a challenge organism (MS2 coliphage, Bacillus subtilis) using a bench-scale parallel beam of known irradiance and exposure time; establishes dose-response curve; (2) Reactor biodosimetry: full-scale UV reactor challenged with same organism in bench test; measured log inactivation converted to RED (Reduction Equivalent Dose) using dose-response curve; RED represents the validated UV dose delivered by the reactor at specified UVT and flow rate; (3) UVT sensitivity: repeat biodosimetry at multiple UVT values (typically 70, 85, 95 percent UVT) and multiple flow rates; derive dose equation or response surface as function of UVT and flow; (4) Sensor correlation: correlate UV sensor reading (mW/cm2) with validated RED; create calibration curves for operational monitoring. Operational dose calculation: D = RED (mJ/cm2) = RED at reference conditions times sensor ratio times UVT correction factor. Validation standards: UVDGM (EPA 2006), DVGW W 294, ONORM M 5873-1 (Austrian), NWRI UV Guidelines (2012). UK DWI: accepts DVGW W 294 or UVDGM-compliant validation for mains systems.
What is UV transmittance and how does it affect UV system performance?
UV Transmittance (UVT) at 254 nm measures the fraction of UV light that passes through 1 cm of water (percentage: 100 percent = perfectly transparent; 95 percent means 95 percent of UV passes through 1 cm of water path). UVT determines how much UV energy reaches the bacteria/pathogen in the water column. Impact on UV dose: at 95 percent UVT (clean drinking water), a reactor delivers near-theoretical dose; at 70 percent UVT (coloured surface water), the same reactor may deliver 30 to 50 percent less dose - requiring higher lamp intensity or lower flow rate to compensate. UV absorbers at 254 nm: natural organic matter (NOM, humic and fulvic acids, measured by UV254 absorbance = 1 - UVT per cm); iron (Fe3+ absorbs at 254 nm; greater than 0.3 mg/L iron significantly reduces UVT); nitrate (absorbs below 240 nm); tannins. Typical UVT values: clean groundwater 95 to 99 percent; treated surface water 85 to 98 percent; secondary wastewater effluent 55 to 75 percent; industrial wastewater 10 to 60 percent. UV system design: sized at minimum UVT expected (10th percentile of seasonal variation); online UVT monitoring (254 nm spectrophotometer) with automatic flow reduction or lamp power increase if UVT falls below design minimum; USEPA UVDGM requires documented UVT monitoring for credit-bearing UV systems.
Do UV systems require chemical addition?
UV disinfection does not require chemical addition for the primary UV process itself - it uses only photons. This is a key advantage over chlorination (chemical handling, byproduct formation) and ozonation (hazardous gas). However, associated chemical needs: (1) UV does NOT provide a disinfectant residual: chlorine or chloramine must be added downstream of UV to protect distribution system water from recontamination; UV inactivates pathogens at the point of treatment but does not persist in the network; UK DWI requires minimum 0.1 mg/L free chlorine (or 0.5 mg/L combined chloramine) at service reservoir; (2) UV lamp quartz sleeve cleaning: automated sleeve wiping (air wipe or mechanical wiper) prevents fouling; periodic acid cleaning (citric acid 5 to 10 percent) of sleeves if biological or calcium fouling is severe; (3) Pre-treatment: UVT may require improvement by coagulation (removing NOM) or iron removal before UV; UVT less than 70 to 75 percent typically requires pre-treatment to achieve cost-effective UV dosing. Advanced oxidation with UV: UV/H2O2 (hydrogen peroxide 5 to 20 mg/L + UV dose 500 to 1,000 mJ/cm2) generates hydroxyl radicals for micropollutant degradation - this process does involve chemical (H2O2) addition but is distinct from UV disinfection.
A water company in Northern Ireland serving 95,000 properties from a lowland reservoir was required by DWI to install a second disinfection barrier following a Cryptosporidium Risk Assessment that identified insufficient treatment credit in the existing chlorination-only process. The works had a UV transmittance of 88% at 254 nm after sand filtration.
The company installed a medium-pressure UV disinfection system (Trojan UV Swift SC6, six lamps per reactor) sized for a maximum flow of 28 MLD at a validated UV dose of 40 mJ/cm2 (4-log Cryptosporidium reduction per the USEPA UV Disinfection Guidance Manual, adopted as the DWI standard). The UV system was validated on-site using biodosimetry (MS2 coliphage surrogate) per the DWI UV Guide. An automated sleeve wiping system with real-time UV intensity monitoring and flow-proportional dose logging was integrated into the SCADA system. Downstream chlorination was retained at 0.3 mg/L free chlorine for distribution system residual.
UV dose was consistently maintained above 40 mJ/cm2 at all flows from 8 to 28 MLD. DWI confirmed 4 log Cryptosporidium credit, closing the outstanding enforcement notice within 14 months of installation. Biodosimetry validation was accepted by DWI without additional testing requirements. THM formation potential in the distribution system fell by 22% as the pre-UV chlorine dose was reduced from 1.1 to 0.4 mg/L, allowing the new UV system to carry the primary disinfection burden.
Questions to Ask Shortlisted Providers
- 1
What is the minimum UV transmittance (UVT) at 254 nm in the water to be treated and at what flow rate must the validated UV dose be achieved?
UV dose is the product of UV intensity and exposure time; lower UVT requires higher lamp output or more lamps to achieve target dose; dose calculation at minimum UVT and maximum flow defines the system capacity.
- 2
What DWI or regulatory log reduction credit is required for Cryptosporidium and other target pathogens, and has a UV validation study been scoped with DWI?
DWI requires UV systems to be validated by biodosimetry (surrogate microorganism) at site-specific flow and UVT conditions; the validated log reduction credit must match or exceed the risk assessment requirement; non-validated systems are not accepted.
- 3
What is the downstream disinfection residual requirement and how will the UV system integrate with existing chlorination?
UV provides no distribution system residual; chlorine or chloramine must be added downstream; the combined system design must achieve DWI minimum free chlorine at service reservoir without creating excessive THMs from chlorination of NOM.
- 4
What SCADA integration, dose logging, and alarm management is required for DWI compliance monitoring?
DWI requires dose logging (mJ/cm2 calculated from intensity and flow) to demonstrate continuous compliance; data must be retained for minimum 1 year and submitted in the Annual Monitoring Report; SCADA alarms on dose below set-point must trigger automatic bypass or shutdown.
- 5
What is the lamp replacement schedule and UV sleeve cleaning requirement, and what are the chemical costs for CIP?
Medium-pressure lamp life is 4,000 to 6,000 hours; low-pressure amalgam lamp life is 12,000 to 16,000 hours; lamp and sleeve replacement is the primary UV operating cost; citric acid CIP for calcium fouling on sleeves is required at sites with hard water.
What Drives Cost in This Category
Medium-pressure UV systems for 10 to 50 MLD drinking water treatment cost GBP 200,000 to 800,000 installed; low-pressure amalgam systems are 20 to 40% cheaper per unit but require more chambers for equivalent dose at high flows.
On-site biodosimetry validation (MS2 or B. subtilis spore surrogate) required by DWI costs GBP 15,000 to 45,000 per UV system; validation must be conducted at minimum UVT and maximum design flow; failed validation requires re-design and re-test.
Medium-pressure lamps cost GBP 800 to 2,500 per lamp; replacement frequency every 4,000 to 6,000 hours (6 to 9 months at continuous operation); lamp replacement including labour adds GBP 0.01 to 0.04 per m3 treated.
Medium-pressure UV energy consumption is 0.02 to 0.06 kWh/m3 at typical doses; low-pressure amalgam at the same dose uses 0.01 to 0.03 kWh/m3; at GBP 0.15 per kWh and 10 MLD flow, annual energy cost is GBP 11,000 to 33,000.
Key Regulations & Standards
Surface water abstractions must undergo Cryptosporidium Risk Assessment; the assessment specifies the log reduction credit required; UV validated at 40 mJ/cm2 is accepted by DWI as providing 4 log Cryptosporidium reduction when biodosimetry validation data is accepted.
Specifies validation protocol requirements for UV systems (biodosimetry using MS2 coliphage or Bacillus subtilis spores); defines dose monitoring requirements (integrated intensity times time), alarm set-points, and data logging obligations for regulatory compliance.
UV disinfection must use DWI-approved equipment installed in compliance with approved operational procedures; any modification to a DWI-approved UV system requires re-notification and potentially re-validation.
H2O2 (hydrogen peroxide, classified as oxidising corrosive under CLP Regulation) used in UV/H2O2 AOP requires COSHH risk assessment, bunded storage with 110% containment, PPE for operators, and emergency response procedures; H2O2 storage and handling must comply with HSE guidance.